Tuesday 26 June 2012

T-shirt shag rug tutorial

 
 


How to Make a T-shirt Shag Rug

 
Supplies: 1 XL t-shirt, cloth scissors, and lots of small t-shirt scraps
the base with a few scraps threaded through

1. Make the base.
For the base of the rug, lay the X-L t-shirt flat and cut a large rectangle out of the shirt, as large as you would like the size of your rug to be. It’s possible to make a larger rug by sewing more t-shirts together- two to make a runner, four to make a large square, etc. You could also cut it into a circle shape for a circular rug.
a rotary board makes cutting easier
perfect sized scraps!

2. Make scraps.
If you are me, you have scraps of t-shirts all over your apartment. If you aren’t, you may need to go to the thrift store and purchase a lot of t-shirts to make into scraps. I would go for 10-12 to start, although I’m not positive exactly how many you will need. Go for more rather than less, and choose complimentary colors, or try to purchase t-shirts that are the same color for a monotone rug. 
Cut these t-shirts into strips that are approximately 5-6’’ long and 1-1 ½’’ wide. You can use scissors, or if you are lucky, a rotary cutter and board, which helps make things faster. Some t-shirt fabrics stretch and so you can pull them to make them longer. Others don’t.  Once you cut a few t-shirts you’ll begin to see what works. Also, don’t be afraid to use imperfect scraps-scraps that have odd edges, have a serged edge on them, are ruffly, etc. They add to the shaggy look of your rug.
holes before and after scraps are threaded through 

3. Cut holes into the base.
Starting 1’’ from the edge of the base, carefully poke or snip horizontal and vertical rows of small holes about 1/2 ’’ to 2/3’’ inches apart. It will look like a big Lite-Brite board without the little pegs! You can also do this as you go along while putting the rug together, as I did, or just go ahead and make all of the holes before you start to thread the scraps into the rug. If you want perfect rows, you can mark the holes first using a ruler to mark the spots. 
see how the scraps share each hole? 

4. Start threading scraps into the base.
Beginning at one corner, thread a strip down through the first hole and back up through the second. Take a second scrap and thread it through the second hole (the same hole you just pulled the first scrap up through) so that it shares this hole with the first scrap, and then pull it up through the third hole.
Continue doing this for a very, very long time… Do this while watching movies, television, when you have a really short moment of time and you don’t know what to do. It will take time, but it will be finished!
the back and top side of the rug- pretty on both sides!


5. Give your rug a haircut.
When you are finished, you can give your rag a little haircut to even out any longer scraps that look off, or you can leave your rug uneven for a shaggier look. But remember, these scraps don’t grow back!
The top side of the rug looks great, but so does the bottom side. Flip the rug over for a new look and feel! If a scrap falls out or gets uneven, simply put it back in or pull it until it is even. It’s very easy to maintain. If you would like to wash it, please use a lingerie bag and run it in a delicate cycle as it could fall apart in the wash. However, the fabric is not delicate itself, so if something were to happen, it can be cleaned.

3 comments:

  1. Hey :) This is Sasha from Lipstickforladybugs :) Thank you so much for telling me about this, i absolutely love this, especially the bottom side of the rug :) Thankfully i have a tonne of old shirts that i was about to throw into the rubbish :P

    ReplyDelete
  2. Thank u Sasha, I am so glad to hear that you not only like the post but you are about to make a rug!!!

    Thanks for visiting!!!!!!

    ReplyDelete
  3. thank you so much I work for an Assisted Living and this will be a great, only I'm going for a blanket. LOL

    ReplyDelete