Design your own stamps without carving

This is an interesting technique of making stamps with silicone caulking and acrylic plexiglass. You can save money and creat stamps with our own design. 

Thanks to http://blog.makezine.com/ for the nice tutorial!

Materials

1/8″-thick acrylic plexiglass; can be found at hardware stores

X-Acto knife

Metal ruler

Silicone rubber caulking (clear) ; can be found at hardware stores

Water-based paint

Brayer

 

Note: You can cut plexiglass to size by scoring a straight line several times using an X-Acto knife and metal ruler, and then placing the plexiglass on a table with the score line over the edge and snapping it in one quick motion.

 
Step 1: Sketch your designs on paper. These botanical designs range between 4″-6″ wide. The leaves are 2″-3″. But your designs can be any size you like.

 
Step 2: Hold the caulk tube vertical and tap it against a flat surface 8-10 times to remove any air bubbles. Cut the tip of the tube with scissors. I usually cut about 1/8″ away. Remember, the size of the hole on the tip of the tube will be the thickness of your lines, so cut cautiously! You can always cut a little more off, but once the tube is cut, you can’t make the opening smaller again.
Place your design under a piece of plexiglass and trace over it with the caulk, making sure you are evenly squeezing the tube and all drawn lines are touching the plexiglass. The harder you squeeze the tube, the thicker your lines will be. In some designs, this might be a desirable effect. You might want to practice on some scrap paper or plexiglass before you start on your stamp.

 
Step 3: Let the caulking cure for 24 hours, and then your stamp is ready.

 
Step 4: On a sheet of plexiglass, squeeze a dollop of paint. To create an ombre print, you will need to use two paint colors at the same time. Load the brayer with paint as you roll.

 
Step 5: Using your brayer, apply the paint on the stamp. You will need to make three to four passes to ensure all lines are covered.

 

Step 6: Carefully press the stamp on your desired surface.




 
Step 7: Create a beautiful botanical pattern! Clean your stamps immediately after use by wiping the surface with a dampened paper towel and any small spaces with a dampened cotton swab. Then, wash gently under running water with a little bit of soap.

Old book paper roses

Source: 100Layer Cake

Craft Supplies:
Paper
Grosgrain Ribbon, ½ Width cut to 4 inch lengths
16 Gauge Wire cut to 15 inch lengths
Glue Gun
Glue Sticks (low temp)
Scissors
Wire Cutters

Step 1: Gather materials. If you are using vintage books or sheet music as your paper source make sure it is still flexible enough to curl with your fingers. The wire can be found at the hardware store, and is sometimes called “black wire” or “annealed coil wire.” Be sure you are using low temp hot glue because you’ll be able to feel it right through the paper petals as you work.

Step 2: Cutting. You will need to stockpile at least 5 different sizes of petals ranging from about ¾ inch wide to 3 inches wide. I cut freehand, and avoid templates, so that each petal is a unique and organic shape. Think of the shapes as little church windows or arches. Some can be pointy, and some can be rounded. For each flower you will need at least 4 of each size. Make more than you need.

Step 3: Shaping. I really feel that this is the most important step to create natural and soft looking flowers. Roll the edges of each petal, and pinch the base slightly. Each one can be done a little differently to give the petals character and roundness. I shape all of my petals before I even begin gluing anything.

Step 4: Rolling the center. You need to cut out one more shape for each flower, and this is for the coiled center of the rose. This shape should be about 2 ½ inches long with a rounded tip. Roll it up into a tube to create its shape. Unroll it and run a bead of hot glue along the inside and re-roll it around the end of your wire. Another dot of glue will hold it in place.

Step 5: Attaching petals. Begin with your smallest petals. Use a single dot of glue, about ¼ inch from the bottom of the petal to attach it to the stem. Your next petal should overlap the first. Continue adding small petals, rotating the stem as you go, always slightly overlapping the last petal you attached. This is where your artistry will come in as you continue to rotate and build. As you begin adding larger petals pinch the bases, as they are much wider. By pinching at the bases you will be rounding out the rose, and creating space between layers.

Step 6: Finishing. The sepals will be made of ribbon, which will also cover your final seams and create a nice polished look. Each rose needs two – 4 inch lengths of ribbon. Wrap them around the stem and secure to the undersides of the petals. Cut a ‘V’ into each end of the ribbons to finish.

Macrame necklace

Source: psimadethis.com via Marianne on Pinterest

DIY delicate gold chain rings

Make your own gold or silver rings from your old chains.

Very easy project that takes only 5 minutes!!!

To see the tutorial click here

Tea Light Lamps

Make a last-second gift, with long drink glasses (possibly used ones), tracing paper (or inkjet transparencies) and tee lights. It's really easy!

You can change of design whenever wanted, or revert the glasses to their initial function.

How are the candles placed and lit? read on at Instructables

DIY Houses by Night lanterns

 A little paper town that lights up your living room!!!

 You can see how to make it in "Followfellow" blog!

Sweater Flower and Pearl necklace

This is a very easy tutorial on how to make that nice necklace.

You can visit Craftaholics anonymous site to see it.